 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MC10ELT24, MC100ELT24 5V TTL to Differential ECL Translator The MC10ELT/100ELT24 is a TTL to differential ECL translator. Because ECL levels are used a +5 V, -5.2 V (or -4.5 V) and ground are required. The small outline 8-lead package and the single gate of the ELT24 makes it ideal for those applications where space, performance and low power are at a premium. The 100 Series contains temperature compensation. http://onsemi.com MARKING DIAGRAMS* * * * * * 0.8 ns tPHL, 0.95 ns tPLH Typical Propagation Delay PNP TTL Inputs for Minimal Loading Flow Through Pinouts Operating Range: VCC = 4.5 V to 5.5 V; VEE = -4.2 V to -5.5 V with GND = 0 V Pb-Free Packages are Available 8 1 SO-8 D SUFFIX CASE 751 8 HLT24 ALYW 1 8 KLT24 ALYW 1 8 1 TSSOP-8 DT SUFFIX CASE 948R 8 HT24 ALYW 1 8 KT24 ALYW 1 H = MC10 K = MC100 A = Assembly Location L = Wafer Lot Y = Year W = Work Week *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. (c) Semiconductor Components Industries, LLC, 2004 1 October, 2004 - Rev. 7 Publication Order Number: MC10ELT24/D MC10ELT24, MC100ELT24 Table 1. PIN DESCRIPTION VEE 1 8 VCC Pin Q, Q TTL D 2 ECL NC 3 6 Q 7 Q D VCC VEE GND NC Function ECL Differential Outputs* TTL Input Positive Supply Negative Supply Ground No Connect *Output state undetermined when inputs are open. NC 4 5 GND Figure 1. Logic Diagram and Pinout Assignment Table 2. ATTRIBUTES Characteristics Internal Input Pulldown Resistor Internal Input Pullup Resistor ESD Protection Human Body Model Machine Model Value N/A N/A > 4 kV > 200 V Level 1 UL 94 V-0 @ 0.125 in 51 Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) Flammability Rating Transistor Count Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. Oxygen Index: 28 to 34 Table 3. MAXIMUM RATINGS Symbol VCC VEE VIN Iout TA Tstg qJA qJC qJA qJC Tsol Parameter Positive Power Supply Negative Power Supply Input Voltage Output Current Operating Temperature Range Storage Temperature Range Thermal Resistance (Junction-to-Ambient) Thermal Resistance (Junction-to-Case) Thermal Resistance (Junction-to-Ambient) Thermal Resistance (Junction-to-Case) Wave Solder 0 lfpm 500 lfpm Standard Board 0 lfpm 500 lfpm Standard Board < 2 to 3 sec @ 248C SO-8 SO-8 SO-8 TSSOP-8 TSSOP-8 TSSOP-8 Condition 1 GND = 0 V GND = 0 V GND = 0 V Continuous Surge Condition 2 VEE = -5.0 V VCC = +5.0 V VI v VCC Rating 7 -8 0 to VCC 50 100 -40 to +85 -65 to +150 190 130 41 to 44 185 140 41 to 44 $5% 265 Unit V V V mA mA C C C/W C/W C/W C/W C/W C/W C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. http://onsemi.com 2 MC10ELT24, MC100ELT24 Table 4. 10ELT SERIES NECL OUTPUT DC CHARACTERISTICS VCC = 5.0 V; VEE = -5.0 V; GND = 0 V (Note 2) -40C Symbol ICC IEE VOH VOL Characteristic VCC Power Supply Current Power Supply Current Output HIGH Voltage (Note 3) Output LOW Voltage (Note 3) -1080 -1950 -990 -1800 Min Typ Max 7.0 18 -890 -1650 -980 -1950 Min 25C Typ 4.5 12.5 -895 -1790 Max 7.0 18 -810 -1630 -910 -1950 -815 -1773 Min 85C Typ Max 7.0 18 -720 -1595 Unit mA mA mV mV NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Output parameters vary 1:1 with GND. VCC can vary 4.5 V / 5.5 V. VEE can vary -4.2 V / -5.5 V. 3. Outputs are terminated through a 50 W resistor to GND - 2 V. Table 5. 100ELT SERIES NECL OUTPUT DC CHARACTERISTICS VCC = 5.0 V; VEE = -5.0 V; GND = 0 V (Note 4) -40C Symbol ICC IEE VOH VOL Characteristic VCC Power Supply Current Power Supply Current Output HIGH Voltage (Note 5) Output LOW Voltage (Note 5) -1085 -1830 -1005 -1695 Min Typ Max 7.0 18 -880 -1555 -1025 -1810 Min 25C Typ 4.5 12.5 -955 -1705 Max 7.0 18 -880 -1620 -1025 -1810 -955 -1705 Min 85C Typ Max 7.0 18 -880 -1620 Unit mA mA mV mV NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 4. Output parameters vary 1:1 with GND. VCC can vary 4.5 V / 5.5 V. VEE can vary -4.2 V / -5.5 V. 5. Outputs are terminated through a 50 W resistor to GND - 2 V. http://onsemi.com 3 MC10ELT24, MC100ELT24 Table 6. TTL INPUT DC CHARACTERISTICS VCC = 4.5 V to 5.5 V; VEE = -4.2 V to -5.5 V; GND = 0.0 V; TA = -40C to +85C Symbol IIH IIHH IIL VIK VIH VIL Characteristic Input HIGH Current Input HIGH Current Input LOW Current Input Clamp Diode Voltage Input HIGH Voltage Input LOW Voltage Condition VIN = 2.7 V VIN = 7.0 V VIN = 0.5 V IIN = -18 mA 2.0 0.8 Min Typ Max 20 100 -0.6 -1.2 Unit mA mA mA V V V NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. Table 7. AC CHARACTERISTICS VCC = 4.5 V to 5.5 V; VEE = -4.2 V to -5.5 V; GND = 0.0 V -40C Symbol fmax tPLH tPHL tJITTER tr/tf Characteristic Maximum Toggle Frequency Propagation Delay (Note 6) 1.5 V to 50% Propagation Delay (Note 6) 1.5 V to 50% Random Clock Jitter (RMS) Output Rise/Fall Time (20-80%) 0.25 1.25 0.25 0.5 0.5 2.0 2.0 0.5 0.5 Min Typ Max Min 25C Typ 400 0.95 0.8 2.5 1.25 0.25 1.25 2.0 2.0 0.5 0.5 2.0 2.0 Max Min 85C Typ Max Unit MHz ns ns ps ns NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 6. Specifications for standard TTL input signal. 7. Devices are designed to meet the AC specifications shown in the above table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained. http://onsemi.com 4 MC10ELT24, MC100ELT24 Zo = 50 W Q Driver Device Q D Receiver Device Zo = 50 W 50 W 50 W D VTT VTT = VCC - 2.0 V Figure 2. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D - Termination of ECL Logic Devices.) ORDERING INFORMATION Device MC10ELT24D MC10ELT24DG MC10ELT24DR2 MC10ELT24DR2G MC10ELT24DT MC10ELT24DTR2 MC10ELT24DTR2G MC100ELT24D MC100ELT24DR2 MC100ELT24DT MC100ELT24DTR2 Package SOIC-8 SOIC-8 (Pb-Free) SOIC-8 SOIC-8 (Pb-Free) TSSOP-2 TSSOP-2 TSSOP-8 (Pb-Free) SOIC-8 SOIC-8 TSSOP-8 TSSOP-8 Shipping 98 Units / Rail 98 Units / Rail 2500 / Tape & Reel 2500 / Tape & Reel 100 Units / Rail 2500 / Tape & Reel 2500 / Tape & Reel 98 Units / Rail 2500 / Tape & Reel 100 Units / Rail 2500 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D AN1406/D AN1503/D AN1504/D AN1568/D AN1642/D AND8001/D AND8002/D AND8020/D AND8066/D AND8090/D - ECL Clock Distribution Techniques - Designing with PECL (ECL at +5.0 V) - ECLinPSt I/O SPiCE Modeling Kit - Metastability and the ECLinPS Family - Interfacing Between LVDS and ECL - The ECL Translator Guide - Odd Number Counters Design - Marking and Date Codes - Termination of ECL Logic Devices - Interfacing with ECLinPS - AC Characteristics of ECL Devices http://onsemi.com 5 MC10ELT24, MC100ELT24 PACKAGE DIMENSIONS SOIC-8 NB D SUFFIX CASE 751-07 ISSUE AC NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0_ 8_ 0.010 0.020 0.228 0.244 -X- A 8 5 B 1 4 S 0.25 (0.010) M Y M -Y- G C -Z- H D 0.25 (0.010) M SEATING PLANE K N X 45 _ 0.10 (0.004) M J ZY S X S DIM A B C D G H J K M N S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 6 MC10ELT24, MC100ELT24 PACKAGE DIMENSIONS TSSOP-8 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948R-02 ISSUE A 8x K REF 0.10 (0.004) M 0.15 (0.006) T U S 2X TU S V S L/2 8 5 L 1 PIN 1 IDENT 4 B -U- 0.25 (0.010) M 0.15 (0.006) T U S A -V- F DETAIL E NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0_ 6_ INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0_ 6_ C 0.10 (0.004) -T- SEATING PLANE D -W- G DETAIL E DIM A B C D F G K L M http://onsemi.com 7 MC10ELT24, MC100ELT24 ECLinPS are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. http://onsemi.com 8 MC10ELT24/D |
Price & Availability of MC10ELT24D
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |